Tweco FP-260 User Manual

FP-200 and FP-260MIG Welding SystemInstruction ManualFORM NO. 0056-1840 EFFECTIVE August 2001Safety and OperatingInstructionsFor Your Safety . . .PLEA

POWER SOURCE CONNECTIONPower RequirementsThis welder is designed to operate on a properly grounded 230 volt, 60 HZ, single-phase alternating current(A

grasp it with pliers so that it cannot exit from the spool. If necessary, straighten it before inserting it in thewire input guide. Insert the wire on

Advantages of Flux Core (FCAW) Welding1. There is no need for gas cylinders.2. Welding outdoors is easier because there are fewer chances that wind bl

DO NOT use the cylinder if you find oil, grease or damaged parts. Inform yourgas supplier of this condition immediately.Regulator Gas Flow Information

SPOT WELDINGSpot welding is possible by replacing the welding nozzle with a spot welding nozzle. You can buy the spotwelding nozzle from any supplier

ADDITIONAL SAFETY INFORMATIONMake sure you read and understand all of the information and instructions contained in this manual BEFOREproceeding.The N

PROBLEM1. Dirty, porous or brittle weld.2. Arc works but is not feeding wire.3. When trigger pulled, there is no wirefeed, weld output or gas flow.Fan

15GENERAL OPERATING TIPSContact tips and nozzles should be cleaned frequently. Spatter buildup may cause bridging between nozzle and tip. Thiscould ca

TROUBLESHOOTING GUIDE FOR FP-300 MIG GUNFP-300 WIRE CONDUIT REPLACEMENTTo remove the conduit:1. Lay the MIG-Gun out on a table or on the floor in a st

Figure 8: FP-200 and FP-26017

Table of ContentspageIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ITEM NO. PART NO. DESCRIPTION QTY. 1 1444-0512 BLACK GAS HOSE 32 1444-0513 INPUT POWER CABLE 13 1444-0514 COMPLETE SPOOL HOLDER 14 1444-0515 MAT FOR

ITEM NO. PART NO. DESCRIPTION QTY. 1 1444-0512 BLACK GAS HOSE 32 1444-0513 INPUT POWER CABLE 13 1444-0514 COMPLETE SPOOL HOLDER 14 1444-0515 MAT FOR

20Figure 9: Electrical Schematic

21FIREPOWER LIMITED WARRANTYSCOPE OF LIMITED WARRANTY: Firepower, a division of Thermadyne Industries, Inc. (here-inafter, "Seller") warrant

LIMITED WARRANTY CLAIM METHOD: To make a claim under this warranty, Purchaser mustnotify Seller of the details of such claim within thirty days of dis

INTRODUCTIONThis User’s Guide provides specific information about your Firepower Welding System. This guide providespertinent information needed to sa

3. NEVER look at the arc without proper protection to the eyes.4. Thoroughly clean metal of rust or paint to avoid producing harmful fumes. Parts degr

3. People with pace-makers or hearing aides should keep far from the power source. In particular cases, specialprotection measures may be required.Red

ELECTRIC SHOCK CAN KILL! Reduce the risk of death or serious injury from shock. Read,understand and follow the following safety instructions. Addition

HEALTH HAZARDSThe welding process can be hazardous to your health. Therefore, follow these precautions:1. ALWAYS wear protective clothing without pock

The use of larger diameter wire makes welding difficult. The results cannot be guaranteed. The manufacturerDOES NOT recommend using larger diameter we

Maximum Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 Amps PeakOutp